Decibel Levels

    How Loud Is 105 Decibels? Task level, operating load and the OSHA table

    Snap Decibel Meter editorial team · Updated 2026-10-25

    Task level, operating load and the OSHA table

    Worker wearing hearing protection
    Illustrative context, not a measurement of this scene.

    Quick answer

    105 dB needs a metric and a task description. OSHA's table contains a 105 dBA / one-hour regulatory row, while a documented chainsaw test reported 106 dB(A) at the operator's ear without load. Neither is a universal 105 dB sound or a personal safe-time promise.

    105 dB compared with another level

    Intensity ratio

    ×10

    10^(difference / 10)

    Pressure amplitude ratio

    ×3.1623

    10^(difference / 20)

    These are mathematical ratios, not perceived loudness or safe exposure time. Compare the same quantity, reference, weighting and time basis; the pressure-to-intensity relationship also assumes matching acoustic impedance. A sound-power label, a peak and an eight-hour exposure are not interchangeable.

    The distance calculator models an ideal point source. It does not predict indoor reflections or establish a safe distance.

    Near 105 dB: one machine can change with load

    The DLG test of a Stihl MS 291 reported 106 dB(A) at full throttle without load and 102 dB(A) at full load. The report lists both values at the operator's ear and separately reports equivalent sound-pressure and sound-power levels under DIN EN ISO 22868. It does not label the machine '105 dB', and averaging the two operating states would manufacture a new unsupported source figure.

    A useful task record distinguishes idle, unloaded operation and actual work. Keep the microphone location and operating state attached to the value. Do not substitute declared sound power or a bystander's measurement for the operator-ear result.

    The one-hour row is not an instruction to keep working

    OSHA Table G-16 lists one hour beside 105 dBA. It is a regulatory exposure row with A weighting and slow response, not a clinical assurance or a universal listening allowance. Mixed-level exposure and the rest of the working day still matter.

    At work, prioritize noise reduction at the source and a competent exposure assessment; hearing protection needs selection and fit appropriate to the circumstances. A phone comparison can help identify changes, but cannot prove compliance or the protection achieved at the ear.

    A separate NIOSH calculation at 105 dBA

    At a hypothetical constant measured 105 dBA, T = 480 / 2^((105 − 85)/3) gives about 4.7 minutes to 100% of the NIOSH recommended daily dose. This is distinct from OSHA's published one-hour row, not an allowance to operate the tested chainsaw for that duration. Other exposure periods still contribute, and neither framework predicts an individual's injury.

    How 105 dB compares with neighbouring levels

    When two levels share the same quantity, weighting and reference, the difference can be converted mathematically; displayed ratios are rounded. Relating pressure to intensity also requires matching acoustic impedance. 105 dB versus 95 dB: 10 times the intensity and 3.1623 times the sound-pressure amplitude; 105 dB versus 115 dB: 0.1 of the intensity and 0.31623 of the sound-pressure amplitude; 105 dB versus 85 dB: 100 times the intensity and 10 times the sound-pressure amplitude.

    These are physical ratios, not perceived loudness ratios. Perceived loudness also depends on frequency content, duration and the listener.

    Method and limitations

    Source figures retain their published metric and conditions. Mathematical examples are hypothetical comparisons, not measured sound-source levels or individual exposure advice.

    Snap Decibel Meter processes audio locally. Its digital signal estimate is not a validated sound-pressure or workplace exposure measurement. Use suitable calibrated instrumentation and a defined procedure for decisions requiring absolute levels.

    Evidence behind the levels on this page

    Every sound level quoted above comes from one of the publications below. For each one we record what was actually measured, the microphone position or distance where that is stated, the metric used, and what the figure can and cannot tell you. Where a source did not state a condition, we say so rather than filling the gap.

    1. Test report 6192 — Stihl MS 291 chainsaw

      DLG · Commissioned model-specific test

      What was measured
      Sound pressure at the operator's ear
      Reported level
      83 dB(A) idle; 106 dB(A) full throttle without load; 102 dB(A) full load
      Distance / position
      Operator position prescribed by DIN EN ISO 22868
      Frequency weighting
      A
      Conditions
      One model, three operating conditions; values are not a daily exposure assessment
      Supports on this page
      Documented observations near 80 and 105 dB; operating condition changes the result
      Limitations
      Not universal chainsaw levels, not a bystander distance measurement, not exactly 80 or 105 dB
    2. 29 CFR 1910.95 — Occupational noise exposure, Table G-16

      OSHA · US federal workplace regulation

      What was measured
      Permissible exposure table, not measured sound-source examples
      Reported level
      95 dBA: 4 h; 105 dBA: 1 h; 110 dBA: ½ h (Table G-16)
      Distance / position
      Exposure at the worker
      Frequency weighting
      A, slow response
      Conditions
      US general-industry regulation; mixed exposures require the regulation's combined-exposure assessment
      Supports on this page
      Exact published table rows, with jurisdiction and measurement basis attached
      Limitations
      Published regulatory durations are not personal safe listening times; NIOSH uses a different criterion and exchange rate
    3. Criteria for a Recommended Standard: Occupational Noise Exposure (98-126)

      NIOSH / CDC · 1998 · Occupational health recommendation

      What was measured
      Recommended occupational exposure criterion
      Reported level
      85 dBA, eight-hour time-weighted average; 3 dB exchange rate
      Distance / position
      Personal exposure at the worker
      Frequency weighting
      A
      Conditions
      Occupational assessment across the exposure period
      Supports on this page
      Distinguishing a daily exposure recommendation from a momentary reading or a medical threshold
      Limitations
      Not a guarantee of individual safety, not an instantaneous threshold, not a household noise rule
    4. University Physics Volume 1, 17.3 Sound Intensity

      OpenStax · Physics textbook

      What was measured
      Definition of an intensity level and sound-pressure relationship
      Reported level
      β = 10 log10(I/I₀); I₀ = 10⁻¹² W/m²
      Distance / position
      Not a source measurement
      Frequency weighting
      Unweighted mathematical definition
      Conditions
      Pressure and intensity relationships require matching propagation conditions and acoustic impedance
      Supports on this page
      Intensity ratio 10^(ΔL/10), pressure-amplitude ratio 10^(ΔL/20); neither is a perceived loudness ratio
      Limitations
      Not a licence to compare sound power, SEL, peaks, weighted levels and time averages as interchangeable quantities